|
Land Rover 109" und 110" 3/4-Truck
cab Umbauanweisung,
oder was zu beachten ist. |
|
|
OLD-STYLE 3/4-FRAME-PARTS
Galvanized frame parts you'll need to fit a
3/4-old-type-hood
(like the 88"/109") on a standard Truck cab / Pick-up Land Rover.
A - Hood mounting frame
B - Drain channel
C - Roop hook
D - Horse shoe and Staple
|
 Click image to see more |
|
FITTING INSTRUCTIONS
Fig. Diagrammatic view of cab and rear body, showing position of
hood mounting frame, drain channels, rope hooks and staples. 88" 3/4 -
109" 3/4 model illustrated.
TO FIT:
1. Position the drain channels against the rear panel so that the lower
edge rests on the rear body front capping; each drain channel should protrude
approximately 1/8in. (3mm) out from the body side capping. The drain channels
are shaped to go round the hoodstick.
2. Using the drain channels as templates, drill six holes 17/64in. (7mm)
diameter and secure the channels to the cab rear panel, using the fixings
provided.
3. Position the hood mounting frame centrally against the cab rear panel
and resting on the drain channels.
4. Using the mounting frame as a template, drill six holes 17/64in.
(7mm) diameter and secure the channels to the cab rear panel, using the fixings
provided.
5. Fit the rear hood sticks in the sockets at the rear corner of the
body and secure with clamp arms, bolts, washers and nuts.
6. Fit the front hood sticks in the sockets at the rear corner of the
body and secure with clamp arms, bolts, washers and nuts.
7. Secure the tie tubes between the sticks, using self-locking nuts.
8. Fit the intermediate hood stick between the tie tubes, securing it
with self-locking nuts.
9. 109" models: secure the hood stick flanges to the pre-drilled
holes in the body side capping, using the fixings provided.
10. Mark centre 9in. (230mm) from the door post and 2in. (50mm) down
from the top of the rear body capping and, using the frond rope hooks as
templates, drill four holes and fix the rope hooks to the body sides, using the
2 B.A. nuts bolts and washers provided.
NOTE: Two rope hooks are handed, 1xLH, 1xRH, the hooks should be towards the
door.
11. Secure the two staples to the rear body, adjacent to the top of the
tailboard, using the existing holes and fixing with the 3/4in. (19mm) long 2
B.A. screws, nuts and washers.
Early Series II models:
12. Place the hood over the hoop sticks and secure to the mounting frame
on the cab. The hood retaining strip should be inserted in the top and side
channels of the hood. Peg the upper retaining strip into the side strip.
13. Fit the lower ends of the two side retaining strips to the staples
on the mounting frame and secure with the short straps.
Late Series II and all Series IIA and III models:
14. Place the hood over the hood sticks and secure to the mounting frame
on the cab. The hood retaining strips should be inserted in the top and side
channels of the hood. Peg the side retaining strips into the top retaining
strip.
15. pull the hood down tight around mounting frame, and mark off
position and drill cab panel for fitting strap retaining stud. Secure hood.
16. Fasten the two straps over the intermediate hood stick, secure the
ropes to the rope bracket on the body sides and, together with the rear ropes,
to the hooks at the rear of the body.
17. Secure the rear curtain straps to the two staples fitted to the rear
of the body.
18. Push the rear curtain side flaps through the side pockets and
secure.
|
109" 3/4-frame with all the parts to fit a
hoot
OLD-TYPE CAB-fixing
fit's a 109" Truck cab Land Rover / Pick-up and 110" 3/4-old
type |
 |
 |
110" 3/4-frame with all the parts to fit a
hoot
NEW-TYPE BULKHEAD fixing
fit's a 110" Truck cab Land Rover / Pick-up 3/4-new type
|
|
| |
|
|
